|
|
 |
|
Carbody Components
Switches and electronical components in the carbody are exposed to extreme environmental conditions. Correspondingly high are the requirements on them: They must be waterproof, protected against ice, as well as robust, precise and durable. Despite their small dimensions, they must also have well defined operating points and extended overtravel. From simple switch/connector combinations through to complex sub-assemblies consisting of multiple switches – we develop the most cost-effective solution for every kind of customer-specific requirement.
|
 |
|
|
| NK17 |
| Component carrier for passenger-door latch (half of the housing) with insert moulding (IP67) for mounting and insertion of sensors in all three dimensions. |
|
|
 |
|
|
| NK09 |
Component carrier for passenger-door latch (half of the housing) with insert moulding (IP67) for mounting and insertion of sensors in all three dimensions.
|
|
|
 |
|
|
| NK03 |
Component carrier for passenger-door latch (half of the housing) with insert moulding (IP68) for mounting and insertion of sensors, electromechanical and electronic components as well as mechanical latch functions, in all three dimensions.
|
|
|
 |
|
|
| NF01 |
| Basic module for RF-key of keyless entry system produced in 2K-technology with insert-moulded sealing. |
|
|
 |
|
|
| NK24 |
| Component carrier with insert mouldings, for the mounting of microswitches at the trunk-locking cylinder. |
|
|
 |
|
|
| NK38 |
| Component carrier for trunk-lock with closing-aid. Hybrid-solution with insert moulding, and FPC as wire carriers, equipped with sensors, varistor, wire-harness and integrated motor-connector. |
|
|
 |
|
|
| NK22 |
| Component carrier for the trunk-lock with insert moulding, (IP68) for mounting and insertion of sensors in all three dimensions. |
|
|
 |
|
|
| NK19 |
| Component carrier for the trunk-lock with insert moulding, integrated connector and watertight potted micro-switch. |
|
|
 |
|
|
| NG04 |
| Insert moulded component carrier in the sidedoor-handle. Including equipped PCB for RF-module of keyless entry system. |
|
|
 |
|
|
| NK01 |
| Component carrier for the passenger door latch with current control switching functions for central locking and with load switching functions for switching off adjustment drives. An insert moulding serves as carrier for switch, plug, electronic components and mechanical lock functions. |
|
|
 |
|
|
| NK20 |
| Component carrier with micro-switches and conductors acting as lock housing (part of the housing). |
|
|
 |
|
|
| NK10 |
| Component carrier for passenger-door latch (half of the housing) with insert moulding (IP67) for mounting and insertion of micro-switches in all three dimensions. |
|
|
 |
|
|
| NM05-0048 |
| DK trunk-handle switch, integrated into a watertight connector-housing (IP67) for the electrical release of the trunk-latch. |
|
|
 |
|
|
| NM05-0033_0034 |
| Switch at the key-cylinder of the trunk-lock for the central locking function (open/close). The switch has an integrated resistor and is watertight according to IP67. It is mounted on a fastening clip with a soldered and filled-in harness. |
|
|
 |
|
|
| NM05-0026 |
| Application in the trunk-lock key-cylinder for the function control of the central locking. An insert moulding, carries two separate watertight (IP67) sub-subminiature snap switches DK. The harness is soldered an filled-in. Various alternative connectors are available. |
|
|
 |
|
|
| NM05-0032 |
| Signal switch in the trunk-lock key-cylinder for the function control of the central locking (open/close). The switch has been designed as an insert moulding, with integrated resistor for carrying a watertight (IP67) sub-subminiature snap switch DK. Several connector variants are available. |
|
|
 |
|
|
| NM05-0008 |
| Signal switch in trunk locks for anti-theft systems. The plug is an insert moulding, for building in a watertight (IP67) micro switch of the DK series. |
|
|
 |
|
|
| NM05-0038 |
| Door handle switch to activate the locking-cylinder heating. |
|
|
 |
|
|
| NM11-0001 |
| Customer specific switch-assembly for comfort locking systems in a sidedoor latch (e.g. for the central locking functions open/close or theft protection systems). The system consists of a double switch with integrated watertight connector (IP67) and meets several OEM customer specific standards. |
|
|
 |
|
|
| NM05-0019 |
| Use in the passenger-door lock key cylinder for the function control of the central locking (open/close). An insert moulding, carries two DK sub-subminiature switches with a soldered and filled-in harness.It fulfils various OEM specific requirements. |
|
|
 |
|
|
| NM05-013_14 |
| Switch-assembly in the sidedoor-lock to control the interior lights and the warning buzzer for the exterior lights. |
|
|
 |
|
|
| NM17 |
| Customer specific striker switch to detect the latch position for interior lighting. Made by dual-component injection-moulding technology. |
|
|
 |
|
|
| NM05-0011 |
| Control of the interior lights and the warning buzzer for the exterior lights as well as the central locking function (open/close) in the passenger door latch. The control meets various OEM customer specific standards. The plug is designed as an insert moulding, for carrying up to three watertight (IP67) sub-subminiature snap switches DK with customer specific additional auxiliary actuator. |
|
|
 |
|
|
| DB2B-BGAA |
| Switch used for headlight cleaning equipment. Switching motor and signal currents with high repeat accuracy and extreme life expectations. Very high resistance against environmental conditions. Customer specific solder terminals. |
|
|
 |
|
|
| DB2C-AGAC |
| Switch used for headlight cleaning equipment. Switching motor and signal currents with high repeat accuracy and extreme life expectations. Very high resistance against environmental conditions. Customer specific solder terminals. |
|
|
 |
|
|
| DCJK-5102 |
| Watertight switch according to IP67 monitoring the change-over blocking of automatic transmissions. |
|
|
 |
|
|
| NM13-0041 |
| Micro switch of the DK series, mounted and potted on a fixation clip to monitor the front hood-latch. |
|
|
 |
|
|
| DK1F-PG06 |
| Watertight micro-switch from the DK-series with simulated roller actuator and fixation pillars to monitor the front-flap lock. Various harness variants are available. |
|
|
 |
|
|
| DK1F-PG01 |
| Application in the front-flap lock of the electronic anti-theft system. The watertight (IP67) sub-miniature snap switch with ice protected additional actuators meets various OEM customer specific demands. The switch has a cable with a flexible hose and can be equipped with different carrier variations to the harness. |
|
|
 |
|
|
| DK1E-HG01 |
| Application with the lock key cylinder for the central locking control in the trunk lock. The central locking functions open/close or as a control signal for the electronic theft protection system. The sub-subminiature snap switch DK with ice protected auxiliary actuator is watertight (IP67) and meets various OEM customer specific demands. Different connector options are available for the the harness. |
|
|
 |
|
|
| DC3E-BGAS |
Control of the trunk lock key cylinder for the central locking (function: open/close) and as signal switch for the theft protection system. The switch is watertight (IP67), carries customer specific built-in parts and a soldered and sealed harness. Several different connector options are available.
|
|
|
 |
|
|
| DK1E-KG01 |
Used in the trunk lock key cylinder for the control of the central locking in the lock key or the electronic theft protection system.The watertight (IP67) sub-miniature snap switch DK with ice protected additional actuators meets various OEM customer specific demands. Different connector options are available for the the harness.
|
|
|
 |
|
|
| NM09-0023 |
| Switch for key cylinder heating in the passenger doors. The watertight switch (IP67) with ice protected auxiliary actuator made of spring steel is mounted above the door-handle. It meets several OEM customer specifications. |
|
|
 |
|
|
| NM09-0001_0002 |
Application in the door lock for the central locking function (open/close). The switch is watertight (IP67) and has an ice protected lever made of spring steel. It meets several OEM customer specifications and has several connector options.
|
|
|
|
|
| Search |
|
Please enter a search term.
|
|
|
| We will give you a call! |
|
|
|
|
| CHERRY Automotive Skills |
|
|
|
|
|
